Belting
Flow Components offers a full line of OEM, Aftermarket, and custom belts at the best price.
V-Belts
Timing Belts
Rooftop Unit
Accu-link Adjustable V-Belts
Energy Saving Timing Belts
Air Handling
Wrapped & Raw-Edged Cogged
Pulleys & Sheaves
Water Cooling Tower Belts
Deep Wedge
Single & Banded
Evaporative Condenser Belts
Cogged Raw-Edged Deep Wedge
Urethane Link V-Belts
Classical Multi Plus A & B Dual Branded for FHP
HTB Timing Belts
Oil, heat, and abrasion-resistant.
The standard trapezoidal tooth timing belt design performs poorly in high torque applications and high power drives at lower speeds. To overcome this disadvantage the High Torque Belt (HTB) was developed using a more efficient tooth profile.
Stock 5 mm, 8 mm and 14 mm pitch HTB timing belts are listed below. Non-standard lengths in these pitches are also available, as are belts with 3 mm pitch.
HTB timing belts are specified by belt pitch length, tooth profile, and tooth pitch code and belt width in millimeters.
3 mm HTB Timing Belts
Many sizes are in stock. Other 3 mm Pitch HTB Belts are available on a made to order basis.
Dual HTB Timing Belts
Dual HTB belts are often used in reversing or serpentine applications.
Special widths are available: use price for next width stock belt. Materials are same as standard belts except that teeth on one side are ground from fiber reinforced neoprene stock.
Power takeoff from ground side is limited to 50% of total belt rating.
Teeth with nylon facing should always be on driver pulley.
Any width available from stock.
Tiger Synchronous Belts
Maximum Performance High-Torque Belt
Special aramid reinforced compounds, along with improved tooth facing and tensile members provide the muscle for the increased horsepower ratings; up to three times that of standard HTB® belts.
Laboratory and customer tested tough!
Tiger Belts® may also be ordered in the standard 8mm pitch HTB® widths of 20 mm, 30 mm, 50 mm and 85 mm, as well as in standard 14 mm pitch HTB® widths of 40 mm, 55 mm, 85 mm, 115 mm and 170 mm.
HTB® drives utilizing TigerBelts® as direct replacements for original HTB® belts will see greatly improved belt life.
Standard Timing Belts
Oil, heat, and abrasion-resistant.
Stock timing belts are listed below. They have fiberglass tension members, neoprene body with nylon covered teeth, all bonded together for maximum strength.
For non-stock widths, specified widths can be cut from our large supply of timing belt sleeves on special order.
Teeth with nylon facing should always be on driver pulley.
Mini-pitch MXL (0.080-inch pitch) timing belts are also available.
Double-Sided Timing Belts
Neoprene fiberglass reinforced
Double sided belts afford power transmission from either side of the belt and are often used in reversing and serpentine applications.
They are specified the same way as timing belts except with a "D" prefix. For example: D240H100. Special widths are cut to order from our sleeve stock for fast delivery.
Double sided timing belts are produced using the same materials as single sided belts, except that the backside is ground from a fiber reinforced special rubber compound. There is no nylon facing on the backside. Power take off on the backside is limited to 50% of the total catalog rating.
Total belt rating is the same as for single sided belts.
Open-End Belting
Specially suitable for linear drives, accurate positioning, metering and reversing applications.
High load capacity, no maintenance cost and very low noise level make these belts a perfect alternative to chain or cable reverse drives.
Double Sided - until now, chain was the only design option for drives requiring long spans and the capability to drive from either side. The advantages of Open-End synchronous belts (no lubrication, no re-tensioning, high-speed capabilities) makes such drives more versatile than ever.
Open-End synchronous belting is specified by an "L" for long length, the belt pitch code and the width code (i.e. L8M-20). Length is specified in feet. Double Sided Open-End is specified "DL" .
Mulberry: (863) 425-4976
Orlando: (407) 634-6766
Tampa: (813) 337-6442
Miami: (305) 901-2144
© 2024 Flow Components & Industrial Supply
604 Prairie Industrial Parkway Mulberry, FL 33860
